This boat has been sold but check out these similar boats nearby

2000 Roger Hill Cruising CutterSold

$375,000

Used
We will let you know when another 2000 Roger Hill Cruising Cutter is available in Juneau, AK

Boat in Juneau, AK 99801 US

builtBuilt in 2000
Year the boat was built
model

Cruising Cutter

Boat model
engine

1 Engine (Detroit VM Motori)

Engine type and count
length

48 feet

Overall boat length
fuel

Diesel

Fuel type
material

Steel

Hull material
Nominal Length
48ft
Length Overall
48ft
Beam
14ft
Max Draft
7ft
Cabins
3
Heads
2
Fresh Water Tanks
300gal
Fuel Tanks
550gal
Holding Tanks
100gal
Hull Material
steel
Engine 1
Engine Make
Detroit VM Motori
Engine Model
494HT-10
Total Power
136hp
Engine Hours
3800
Engine Type
inboard
Fuel Type
diesel
Engine Year
2000
Drive Type
direct
Propeller Type
3-blade
Propeller Material
bronze
Wind Generator
Tender
Solar Panel
Swimming Ladder
Bow Thruster
Washing Machine
Electric Bilge Pump
Oven
Microwave Oven
Air Compressor
Air Conditioning
Electric Head
Heating
Hot Water
Refrigerator
Fresh Water Maker
Deep Freezer
Sea Water Pump
Battery Charger
Depthsounder
Radar
Wind Speed And Direction
Computer
Tv Set
Navigation Center
Plotter
Dvd Player
Autopilot
Radio
Compass
Cd Player
Gps
Vhf
Bimini Top
Shore Power Inlet
Generator
Inverter
Steering Wheel
Tiller
Spinnaker Pole
Accommodations
  • Open Salon/Galley/Pilothouse layout with 2 heads plus rear queen size private with ensuite and full stand up shower. Forward Vberth with two 6'6” berths.  Additional sea berth in companionway. With the saloon sofa, the yacht can comfortably sleep six adults. Light colored maple interior and rich mahogany with inlaid maple cabin sole throughout
  • U-Shaped Galley for convenience and easy chef access, safe and secure while at sea; multiple storage cupboards, drawers and additional large underfloor storage. Corian counters, double stainless sink. Exceptionally large refrigerator and separate huge freezer big enough for months of provisions.
  • Navigation station with full remote monitoring, controls and navigation. Full sized chart table with lift up storage for additional full sized navigation charts and instruments. 
  • Private aft Master Suite w/ dual access queen bed, individual reading lights, overhead hatch and four portholes, two vented closets and multiple storage drawers cupboards. TV. Fan. Private ensuite with fresh water toilet, sink with cabinets. Washing Machine. Fully private, spacious walk-In shower with fibreglass enclosure. 
  • Forward head with cabinets, electric freshwater flush toilet, stand up shower and night lighting.
  • Hurricane rated glass with reflective coating in salon windows with acrylic panels to attach as storm protection or additional insulation.
  • Entire sole of main salon hinges up to allow excellent access to all machinery
  • All corners within are rounded to avoid bodily injury while at sea. All floorboards are screwed down and all cabinets can be screwed shut to prevent accidents at sea.
  • Generous and thoughtfully designed amounts of storage throughout the boat
Climate and Environmental Control
  • Webasto ST90 Hydronic Diesel Heating System with 3 Air Handling Units / zones. Winter and summer control valves.

  • Hot water and engine block heater via Webasto heater with zone valves for each

  • CruiseAir Heat Pump for air conditioning (heating and cooling)

  • Engine heat exchanger for saloon while motoring

  • Eberspacher diesel hot air heating

  • 7 Opening ports with screens

  • 4 opening hatches with screens

  • 5 removable dorade vents.

  • Full boat shade cover

  • Hull, deck and superstructure interior insulated with fire retardant insulating foam

    sprayed throughout

Galley, Heads and Plumbing Details
  • SeaRecovery 40 gallon/hour reverse osmosis water maker with dual 40” membranes, 2.5hp electric high pressure pump and 0.5hp feed pump. Two large separate 5 micron oil and sedement pre-filters

  • Exceptionally large refrigerator and freezer with custom refrigeration unit, two expansion valves and three refrigeration evaporator plates.

  • Force10 3 burner propane stove with oven and broiler

  • 2 20 Lb Propane tanks

  • Mademsa inverting microwave - built in

  • Solid Surface Corian Countertops in galley and heads with sculpted fiddles

  • 350 Gallon fresh water capacity in 2 stainless steel tanks

  • Jabsco hot/cold pressurized water system throughout

  • Hot/cold fresh water shower on aft swim platform

  • 1 Electric head, one manual head – both flush with fresh water, not sea water

  • Separate fiberglass stall shower in rear owners head

  • Midea Ultracube Washing machine with digital controls built into master ensuite

  • Black water holding tank with macerator pump - 50 gallons

  • Gray water tank - 50 gallons

  • 4 below waterline thru hull fittings with marelon seacocks

  • Tank-Tender fuel/water/holding tanks level; gauge

Entertainment
  • Kenwood AM/FM Radio / CD player with 3 Bose Speakers

  • TV with CD Player and external hard drives. Extensive movie library.

Electrical System
  • 8 KW Nothern Lights Generator w/ 2795 hours

  • 125W 24v solar panel mounted on arch with PWM regulator

  • EclecticEnergy D400 5 blade 400w wind generator with Flexcharge 25aNCHC

    controller driving ultra high amp mercury switched contactors for overspeed protection

  • Heart Freedom 20 24v/250v Modified Sine Wave Inverter/Charger

  • Heart 2500W 24v/250v Sine Wave Inverter

  • Mastervolt IVC 8772 12v/12v converter for stabilised instrument supply

  • Mastervolt IVC 8772 24v/24v converter for stabilised autopilot supply

  • 8Group 31 AGM House Batteries

  • 2 Group 31 AGM main engine starting batteries

  • Heart Link 1000 battery monitor / charge controller

  • Hart EVI AC & DC Circuit breaker panels with meters

  • 250v, 24v 12v systems. 115V via portable power transformer

  • Victron 3.6KW Isolation Transformer

  • Ample Technologies NextStep regulators for engine and generator alternators.

  • Stator RMC-142D Earth Fault Relay for Generator<>A/C bus protection

  • 30A Shore power receptacle w/ 50' power cord

  • 3 12V DC Outlets

  • 10 250V AC outlets including 6 GFCI

  • Tank Sentry TS1501 monitor for diesel day tank with capacitance level probe (Princeton Technologies) and Jabsco lift pump giving automatic level control

  • Hart Systems Tank Tender pneumatic level monitoring of main diesel and water tanks

  • Vacuum Cleaner, blender

  • All batteries, electrics and electronics are in a dry closet separate from the machinery space and protected from all fresh water and salt water mishaps. An amazingly important issue in a sailboat where equipment is typically jammed together.

Navigation Electronics
  • Raytheon R40XX 4KW radar with alarm - mast mounted

  • Furuno GPS-32 GPS at nav station

  • Furuno SC30 Satellite GPS and Heading Indicator

  • ICOM MA-500TR AIS Transponder with independent GPS, display and chart overlay

  • Raytheon ST60 Depth Sounder in cockpit

  • Raytheon ST60 Wind Indicator in cockpit

  • Raytheon ST60 Seed Indicator in cockpit

  • Raytheon ST60 Course compass in cockpit

  • Probe Interphase Twin Scope forward looking sonar

  • Raytheon ST 7000+ Autopilot in cockpit with additional control at nav station

  • Raytheon ST60 Multifunction display at nav station

  • Sunnto Compass on Steering Pedestal in cockpit

  • OpenCPN, Maxsea, SAS Planet charting software with massive digital chart library

  • Custom Satellite navigation chart images of all South Pacific Atholl passes

  • Custom Satellite navigation chart images of anchorages in Chilean Archipeligo and Beagle Chanel

  • Paper navigation charts of all of the Pacific, Aust, NZ

  • Library of cruising guides and books related to South America, South Pacific, Alaska

  • Prosser Weathertrend Digital Barometer

Communications Systems
  • ICOM M602 25watt VHF at nav station with Remote Mic for cockpit and masthead/arch antenna

  • ICOM IC M710 SSB/ Ham radio with automatic tuner .

  • PTC lle Modem with PC-lll software upgrade for weather fax and email

  • ICOM MA-500TR AIS transponder with masthead/arch antenna

  • Standard Horizon submersible VHF Radio

  • Computer aided communication via AirMail, SailMail and RMSExpress.

Propulsion and Auxiliary Systems
  • VM 494HT-10 136 Hp turbocharged diesel main engine with 3800 hours

  • Side Power Sleipner 7 Hp 24V Bow Thruster. Control on steering pedestal

  • 1.5" Stainless steel shaft

  • Dripless shaft seal

  • Thorndon custom composite shaft bearings

  • Polyflex Shaft Coupler

  • Hydraulic Shaft Brake for autofeathering propeller

  • MaxProp 610.83 bronze self feathering propeller

  • Dual Racor fuel filters for main engine. Third Racor for the Generator

  • Aqualift muffler and exhaust system

  • Oil change pump

  • 500 gallon fuel capacity in 2 keel tanks and two bilge tanks and 50 gallon day tank

Sails and Rigging Details
  • Custom Aluminum Mast with double spreaders

  • Dyform 1 x 19 Standing Rigging with additional fore and aft baby stays

  • LeisureFurl In-Boom roller furling mainsail system

  • Full battened (5) mainsail with reefing control led to cockpit

  • 135% Roller Furling Genoa on Furlex Roller Furler

  • 80% Roller Furling Staysail on Furlex Roller Furler

  • 1800 Sq Ft 1.5 oz multi colored cruising spinnaker

  • Two Spectra Spinnaker halyards external to the mast using masthead turning blocks.

  • Spectra running backstays with 2 to 1 tensioning blocks

  • Rigid Boom Vang with downhaul system led to cockpit

  • 2 Lewmar # 64 self-tailing primary winches in cockpit

  • 2 Lewmar # 48 self-tailing cockpit winches in cockpit

  • 1 Lewmar # 48 electric power self-tailing in cockpit for all sail controls

  • 2 Lewmar # 48 self-tailing winches on mast

Safety and Hull Details
  • 4 Watertight Compartments built into hull

  • Deck stepped mast with compression post and ring frames to pick up all mast, stanchion

    and keel loads

  • Crash frames within hull circumferentially at the waterline and half frame at bow.

  • Schedule 80 steel pipe at keel leading edge for collision protection

  • Stainless steel partial rudder skeg with sacrificial lower half of rudder blade

  • GME Aquastat 406MHz EPIRB w/ GPS

  • 3 Fire extinguishers

  • Tri-Color sailing light / anchor light / strobe light

  • Double Lifelines on 32" high stainless steel stanchions with stainless steel bow and

    stern pulpits

  • Stainless steels hand holds in/out of companionway door, along top of pilothouse and

    along cabin top

  • 4 automatic bilge pumps with alarms

  • 1 Whale manual bilge pump

  • XINTEX S-2A Propane detector with 2 sensors

  • Sunspot 2 million candlepower 12v hand held spot light

  • Carbon monoxide detector/alarm

  • 3 battery powered smoke alarms

  • Air Horn

  • Red courtesy Night Lights throughout the yacht

  • Night lighting in galley and forward head

    Additional

Steering System
  • Hydraulic steering with 48" wheel

  • Raymarine 100 Autopilot computer driving dual electric hydraulic pumps and dual

    rams, Systems are duplicated and can be swapped underway using valves in the event of autopilot hydraulic or electrical failure. Controls for autopilot in cockpit and nav station in saloon

  • Skeg hung stainless steel rudder blade with sacrificial lower 30% in case of impact

  • Custom tiller emergency steering

Ground Tackle
  • Rocna 55 Lb anchor with 300' of 3/8" HT galvanized chain

  • Spare Fortress anchor with 30' of HT galvanized chain and 300' of 3/4" rode

  • Muir VRC2500 Electric Windlasses with controls at bow, cockpit and forward berth

  • Articulated stainless steel bow roller fittings

  • Foredeck Bollard and chain harnass

  • Chain deck rings and chain hooks

  • Snubber

  • Salt Water anchor / deck wash down system

Tender and Dive Equipment Included
  • Highfield 12' RIB dinghy with launching wheels

  • Mercury 15 hp outboard engine

  • Alkin 2.5hp electric air compressor continuously rated for multiple fills to 3500psi

  • Dive gear with 4 bottles, regulators, BCDs, fins, weights, wetsuits.

Additional
  • Design plans, build photos
  • US Customs importation documents

  • USCG documentation

  • AK registration

  • Complete set of paper manuals for all systems – organized by category in a dedicated filing cabinet between saloon captains chairs. This is duplicated digitally on boat computer

  • Wiring schematic for the boats electrical system

  • Huge collection of paper navigation charts for the Pacific and Indonesia.

  • Comprehensive library of cruising reference books.

  • Spares and tools for onboard systems

  • Integrated Cockpit Bimini with fold-down frame.

Docking Gear
  • 6 Polyform fenders

  • Assorted dock lines

  • 6 Stainless steel deck cleats

  • Custom stainless steel rollers on stern deck mooring

  • Bollard on foredeck

Disclaimer

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. Buyer should assume that items on the vessel at the time of viewing, but not specifically listed on this specification sheet, are not included with the sale of the yacht, and should instruct his agents, or his surveyors to investigate such details as the buyer desires validated. Buyer assumes responsibility to verify all speeds, consumptions, capacities and other measurements contained herein and otherwise provided, and agrees to instruct his surveyor to confirm such details prior to purchase. This vessel is subject to sale, price and inventory changes, and withdrawal from market without notice.

Disclaimer

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.

Overview from around the web 2000 Roger Hill Cruising Cutter

Customers praise the 2000 Roger Hill Cruising Cutter for its exceptional craftsmanship and sturdy design, making it a reliable choice for serious cruisers

Many highlight its comfortable and spacious interior, which is well-suited for extended voyages. The cutter rig offers excellent sailing performance and ease of handling, even in challenging conditions. Owners also appreciate the attention to detail and quality materials used throughout the boat, contributing to its durability and timeless appeal. Overall, the Roger Hill Cruising Cutter 2000 is celebrated for combining traditional aesthetics with practical features, earning high marks from those who value both style and seaworthiness.

The Biggest Pros and Cons

The 2000 Roger Hill Cruising Cutter is a well-regarded sailing vessel known for its classic design and solid construction. Here are some of its pros and cons:

Pros

Robust Build: Crafted with durable materials, offering excellent seaworthiness and longevity.

Traditional Design: Features a timeless cutter rig that provides versatile sail plans, making it suitable for various wind conditions.

Spacious Interior: Designed with comfortable living quarters, ideal for extended cruising.

Good Handling: Known for stable and manageable sailing characteristics, even in challenging conditions.

Ample Storage: Plenty of room for provisions and gear, supporting longer voyages.

Cons

Weight: The solid construction results in a heavier vessel, which may affect speed and maneuverability.

Maintenance: Traditional materials and design can require more upkeep compared to modern composites.

Speed: Not designed for high-speed performance; prioritizes comfort and stability over racing capabilities.

Cost: Quality craftsmanship can come with a higher price point both in purchase and maintenance.

Made For

The 2000 Roger Hill Cruising Cutter is designed for sailors who value traditional craftsmanship combined with excellent cruising capabilities. Ideal for those seeking a sturdy, comfortable, and seaworthy vessel, this cutter suits both experienced bluewater cruisers and adventurous coastal sailors. Its classic design and thoughtful layout make it perfect for long-distance voyages as well as leisurely weekend trips, appealing to individuals or couples who appreciate reliability, ease of handling, and timeless style on the water.

Finance your dream boat!

Use our boat payment calculator to estimate monthly payments for 2000 Roger Hill Cruising Cutter. Enter your down payment, choose a loan term, and adjust the interest rate to see an instant payment estimate — ideal if you're calculating boat payments before you enquire. Wondering how much does a Cutter cost in today's market, or how much does a Roger Hill cost for similar models? This boat financing calculator helps you compare scenarios in seconds, whether you're considering used boat financing or a new purchase.
Monthly payment
$4,256.14/mo
$
$
Loan amount$ 375,000
OR
%

Finance your dream boat!

Use our boat payment calculator to estimate monthly payments for 2000 Roger Hill Cruising Cutter. Enter your down payment, choose a loan term, and adjust the interest rate to see an instant payment estimate — ideal if you're calculating boat payments before you enquire. Wondering how much does a Cutter cost in today's market, or how much does a Roger Hill cost for similar models? This boat financing calculator helps you compare scenarios in seconds, whether you're considering used boat financing or a new purchase.
Monthly payment
$4,256.14/mo
$
$
Loan amount$ 375,000
OR
%

Contact Rubicon Yachts

3300 Powell Street, Suite 105, Emeryville, CA, 94608

Be the first to know when similar boats hit the market

Get notified when new boats become available

Meet the Broker

Address

3300 Powell Street, Suite 105
Emeryville, CA 94608

Boat Location

Be the First to Know

Get notified when new boats become available.