2017 Nitro Z19
$23,475
Boat in Owatonna, MN 55060 US
Built in 2017
Z19
1 Engine (Mercury)
19.3 feet
Gas
Fiberglass/Reinforced
At 19' 4" and with maximum 200HP, the NITRO® Z19 is fast enough for the most demanding tournament angler, big enough for those who fish with a garage-load of tackle, and nimble enough to get into places where bigger, heavier boats can't. This is thanks in part to our exclusive NVT™ (NITRO Vortex Technology™) hull, which improves holeshot, acceleration and overall performance.
The NITRO Z19 is rigged with a Minn Kota® Ultrex™ trolling motor and a custom, factory-matched trailer with GALVASHIELD® corrosion protection.
- Standard w/Mercury® 200 L OptiMax® Pro XS
- NVT™ (NITRO® Vortex Technology™) hull w/Rapid Planing System™ for better handling & a drier ride
- 38 sq. ft. bow deck for maximized fishability & comfort
- Room at the bow & console for optional flush-mounted 12" (30.48 cm) fishfinders
- Oversized, lockable port & starboard bow rod lockers w/lid assists for rods up to 8' (2.44 m) long
- 2 insulated aft 19-gal. (71.92 L) Guardian™ livewells w/digital timers
- Low-profile gunnels w/integrated navigation lights to maximize deck space
- Step-to-bow 62-qt. (58.7 L) insulated cooler w/removable trash receptacle
- Port-side partner rod ramp & dedicated net storage behind seats
- Length:19' 4"
- Beam: 94'
- Bottom width: 74'
- Max. recommended HP: 200 HP
- Fuel capacity: 50 Gallons
- Max. person capacity: 4 Persons
- Max. person weight: 500 Lbs.
- Max. weight capacity : 1375 Lbs.
- Depth inside: 18.5'
- Transom height: 23'
- Deadrise: 16 Degrees
- Draft: 15'
- Approx. weight: 1850 Lbs.
- Approx. package weight: 3249 Lbs.
- Package width: 8' 6"
- Storage length: 22' 7.25"
Comfort, Convenience & Peace of Mind
- NMMA Certified
- Flotation meets or exceeds NMMA & U.S. Coast Guard requirements
- EPA-compliant fuel system
- Non-skid bow mat
- 5 drink holders
- 4 stainless steel pull-up cleats
- Integrated fold-down stainless steel reboarding ladder
- Stainless steel passenger grab handle(s)
- Built-in tournament ruler & holder
- Fire extinguisher
- Horn
- Paddle
Console
- Hydraulic steering w/tilt
- Removable molded, tinted windscreen
- Ready to accept optional removable port console
- Custom-molded modular console w/2-tone paint scheme
- Veethree® multi-function instrumentation w/speedometer/fuel gauge, tachometer/trim gauge, voltmeter gauge & water pressure gauge
- Dash light dimmer
- LED courtesy light
- Below-console 12V outlet
- Hot Foot™
Construction & Exterior
- Deck & hull chemically bonded & mechanically fastened w/stainless steel fasteners
- Transverse & longitudinal fiberglass foam-filled stringer system
- Full-width fiberglass-encapsulated composite transom
- 16-oz. (.45 kg) plush, marine-grade cut pile carpet on decks & floor
- Carpet edge trim
- Low-profile gunnels to maximize interior space & fishing decks
- Heavy-duty rub rail
Electrical
- Bow panel w/trolling motor receptacle, anchor/light switch & trim switch w/capability to flush mount 12" (30.5 cm) graph
- 1,000 GPH (3,785.41 LPH) bilge pump
- LED console courtesy light
- Integrated bow navigation lights w/stowable stern light
- Manual LED-lighted bow storage
- Automotive-style labeled fuse panel w/cover
- Interstate® cranking battery
- 2 heavy-duty Interstate® Series 29 trolling batteries
- 2-bank (8 amps total) battery charger w/exterior receptacle
- 6-gauge trolling motor wiring/w 50-amp circuit breaker
- Master power switch
- Waterproof Deutsch plugin gauge connectors
- Water-resistant connectors on all pumps & navigation lights w/protective abrasion-resistant wrap
Interior
- Expansive 38 sq. ft. bow deck
- Step to bow deck w/insulated 62-qt. (58.7 L) cooler & removable trash receptacle
- Helm & passenger bucket seats
- Bike seat w/pedestal
- Folding fishing seat w/composite frame
- Designated net storage behind seating
- Trolling motor pedal recess for Minn Kota® & MotorGuide® trolling motors
- Oversized, lockable port & starboard bow rod lockers w/lid assists for rods up to 8' (2.44 m)
- Molded-in drainage channels around bow storage compartments
- Port & starboard bow rod hold-down straps
- Oversized lockable center bow storage locker
- Partner rod ramp w/rod handle organizer & rod holder strap
- Lift-out, molded aft storage boxes that will accept seven 3700 tackle trays
- Molded utility rigging compartment for easy access to batteries & pumps & easy cleanup
- Lockable compression latches
- Footrest w/non-skid mat under console(s)
- Insulated aluminum lids w/welded corners
Livewell System(s)
- 2 insulated aft 19-gal. (71.92 L) Guardian™ livewells w/digital timers
- 750 GPH (2,840 LPH) livewell recirculation/pump-out system
- Dual remote drain controls
- Rotomolded w/rounded corners
Performance
- NVT™ (NITRO Vortex Technology™) hull
- Rapid Planing System™ for quicker holeshots, better handling & a drier ride
- 3" (7.62 cm) adjustable jack plate (Verado® only)
- 8" (20.0 cm) adjustable jack plate (Optimax® only)
- Rigging tube for organized wiring & abrasion resistance
- Stainless steel propeller
Trailer
- Custom-fit, factory-matched, single-axle NITRO® trailer w/powder-coat finish & GALVASHIELD® corrosion protection
- 15" (38.1 cm) chrome wheels w/radial tires
- No Touch Vortex hub lubrication system for no-maintenance peace of mind w/6-yr. 100,000-mile limited warranty
- Spare tire carrier (spare tire avail. at additional cost)
- All-welded rectangular tube frame for a unitized structure w/exceptional strength-to-weight ratio
- Space-saving swing-away tongue to reduce storage length
- 1,200-lb. Fulton swing-up locking jack w/swivel wheel
- Heavy-duty winch w/nylon strap & bow safety strap
- Outboard motor support to reduce hull & transom stress while towing
- Carpeted bunks & fender boards to protect hull
- Submersible lights
- Safety cables
Trolling Motor
- Minn Kota® Ultrex™ foot-control trolling motor
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice. All sales are final. No returns accepted.
Price History
| Date | Event | Price |
|---|---|---|
| 5/7/26 | Initial price | $23,475 |
2017 Nitro Z19 Video Tours
Boattest.com Review
Overview
The Nitro Z19 Z-Pro package is a 19-foot bass boat designed specifically for serious tournament anglers. Positioned to fill a gap in Nitro's lineup for a tournament-focused model in the 19-foot range, the Z19 Z-Pro offers a balance of size and performance. Measuring 19 feet 4 inches, it features ample casting platforms and a 16-degree deadrise at the transom, providing enough stability and handling capability to navigate choppy waters while remaining compact enough to fish in tight spaces near docks and structures.
Power and Performance
Our test boat was powered by a Mercury Optimax 200 Pro XS outboard engine with a 1.75-to-1 gear ratio, turning a Fury 14x25 three-blade stainless steel propeller. With two people aboard, a full fuel tank, and test gear, the boat weighed approximately 3,015 pounds. It achieved a top speed of 68.4 mph at 5,600 rpm. The most efficient cruising speed was recorded at 3,500 rpm, where the boat ran at 39.1 mph while consuming 7.4 gallons per hour, resulting in a fuel economy of 5.3 miles per gallon and a range of 239 statute miles with 10% fuel reserve. The Z19 Z-Pro utilizes Nitro's Vortex Technology (NVT) hull design, characterized by parabolic scalloped shapes that curve upward, enhancing turning ability and lift. Additionally, the Rapid Planning System incorporates a transom setback and a notch ahead of the motor to deliver cleaner water to the prop, improving propulsion efficiency. The hull design also minimizes water surging into the cockpit during deceleration, keeping the aft casting deck dry. Handling was confident and stable, with no chine walking or prop ventilation observed during wide arcs and tight turns.
Exterior Design and Deck Features
The Z19 Z-Pro's exterior is thoughtfully designed for tournament fishing. The aft casting deck measures 44 inches fore to aft and 80 inches across, providing 24 square feet of casting space. A dedicated socket allows for secure placement of a portable seat. The boat includes an 8-foot Power-Pole shallow water anchor mounted at the stern, and the Mercury Optimax 200 Pro XS is installed on an 8-inch jack plate. Forward on the aft deck, there are two insulated roto-molded 19-gallon Guardian Livewells with digital timers, oxygen generators, remote drain controls, and high-capacity recirculating and aerator pumps. The livewells are baffled and colored blue to reduce bait stress. Storage is ample, with locking hatches on each side containing removable tubs sized for seven Plano 3700 Series tackle boxes. A large center hatch provides access to the power pole pump, trolling batteries, cranking battery, and a three-bank 30-amp battery charger. Additional features include a two-stroke oil tank, a 1,000-gallon-per-hour bilge pump, and gel-coated stringers for durability.
Bow and Forward Deck
The bow casting deck offers 34 square feet of space with anti-fatigue padding beneath the marine carpet for comfort during extended fishing sessions. The bow is equipped with a Minn Kota Fortrex trolling motor delivering 80 pounds of thrust on a 45-inch shaft. Controls for the trolling motor, a second Lowrance HDS-7 structure scan fish finder, light and trim switches, a recessed foot pedal, and a cup holder are all conveniently located. Storage includes a port locker for rods up to eight feet long, a large lighted center compartment with customizable partitions, and a starboard locker with racks for the stern light, seat pedestals, and a paddle. Bungee cords on each side of the bow deck provide quick and secure rod storage.
Helm and Seating
The helm is equipped with multifunction V3 gauges and a Lowrance HDS-7 fish finder flush-mounted both at the bow and helm stations. The driver benefits from a hot foot throttle, tilt hydraulic steering wheel, and a pro-trim turn signal style trim switch that allows hands-on-wheel operation. Push-button accessory switches flank the wheel, with livewell recirculation controls on the starboard side. The shift control is ergonomically positioned, with livewell fill switches just ahead. A storage tray with a rubber mat and power pole controls are located near the shifter. Seating features automotive-style seats with wraparound backrests and angled cushions designed to hold occupants securely at high speeds. An optional second console can be bolted outboard to port, providing additional rod storage with a carpeted ramp for rod tips.
Additional Features and Trailer
Additional conveniences include a roto-molded 62-quart cooler with improved insulation and a tray to keep sandwiches separate from ice, a trash receptacle, and multiple cup and tool holders. The boat comes standard with a tandem axle trailer featuring GalvaShield coating and Surge disc brakes, enhancing durability and safety during transport.
Conclusion
The Nitro Z19 Z-Pro package is a well-rounded tournament bass boat that combines thoughtful design, advanced hull technology, and comprehensive features to meet the demands of serious anglers. Its performance on the water is confident and efficient, with excellent handling and fuel economy. The ample storage, livewell system, and ergonomic controls contribute to a tournament-ready experience right out of the box.
Overview from around the web 2017 Nitro Z19
The 2017 Nitro Z19 has received positive feedback from customers who appreciate its performance, design, and features
Many owners highlight the boat's impressive speed and stability, making it a great choice for both fishing and recreational use. The spacious layout and ample storage options are frequently praised, providing convenience for anglers as well as families. Users also enjoy the advanced fish-finding technology and comfortable seating, which enhance the overall boating experience. The durable construction and quality materials used in the Nitro Z19 are noted as key aspects that contribute to its longevity and reliability. Overall, the 2017 Nitro Z19 is seen as a well-rounded boat that delivers on performance, comfort, and functionality, making it a favorable choice among boat enthusiasts.
Made For
The 2017 Nitro Z19 is designed for avid anglers and boating enthusiasts who are looking for a high-performance fishing boat that combines versatility, functionality, and comfort. This model caters to both seasoned bass fishers and casual recreational boaters, offering ample space for gear, comfortable seating, and advanced features that enhance the fishing experience. Features such as a spacious casting deck, integrated storage options, and powerful outboard performance make the Nitro Z19 ideal for those who appreciate a well-equipped vessel. With its sleek design and attention to detail, this boat is perfect for anyone wanting to enjoy both fishing expeditions on large lakes and leisurely days on the water with family and friends. Whether you're targeting tournament-sized fish or simply cruising, the 2017 Nitro Z19 delivers the performance and reliability needed for an unforgettable time on the water.
Be the first to know when similar boats hit the market
Get notified when new boats become available
Boats For Sale in Minnesota, United States Similar to the 2017 Nitro Z19
Compare with similar boats and find the perfect one for you.
 2017 Nitro Z19 | |||||
|---|---|---|---|---|---|
| $23,475 | $40,639 | $46,699 | $50,699 | $53,944 | $61,999 |
| Owatonna | Forest Lake | Duluth | Owatonna | Shakopee | Duluth |
| 19' | 19' | 19' | 19' | 19' | 19' |
| Mercury | MERCURY MARINE | MERCURY MARINE | Mercury | MERCURY MARINE | MERCURY MARINE |
| 200 hp | 150 hp | 150 hp | 150 hp | 200 hp | 225 hp |
| 25 | 56 | 366 | 334 | 105 | 374 |
Other Nitro boats for sale in Minnesota, United States
Meet the Broker
Address
Boat Location
Contact Cabela's Boating Center | Owatonna, MN about 2017 Nitro Z19
3900 Cabela Drive, Owatonna, MN, 55060
Login with Google